A Soak Pit, also known as a soakaway or leach pit, is a covered, porous-walled chamber set in the ground that allows water to slowly percolate. Pre-settled effluent from a water-based collection and storage/treatment or a (semi-) centralised treatment technology is discharged to the underground chamber from which it infiltrates into the surrounding soil.General term for a liquid that leaves a technology, typically after blackwater or sludge has undergone solids separation or some other type of treatment. Effluent originates at either a collection and storage or a (semi-) centralised treatment technology. Depending on the type of treatment, the effluent may be completely sanitised or may require further treatment before it can be used or disposed of.Mixture of solids and liquids, containing mostly excreta and water, in combination with sand, grit, metals, trash and/or various chemical compounds. A distinction can be made between faecal sludge and wastewater sludge. Faecal sludge comes from on-site sanitation technologies, i.e. it has not been transported through a sewer. It can be raw or partially digested, a slurry or semisolid, and results from the collection and storage/treatment of excreta or blackwater, with or without greywater. Wastewater sludge (also referred to as sewage sludge) originates from sewer-based wastewater collection and (semi-)centralised treatment processes. The sludge composition will determine the type of treatment that is required and the end-use possibilities.Describes technologies for on-site collection, storage, and sometimes (pre-) treatment of the products generated at the user interface. The treatment provided by these technologies is often a function of storage and is usually passive (i.e. requires no energy input), except a few emerging technologies where additives are needed. Thus, products that are ‘treated’ by these technologies often require subsequent treatment before use and/or disposal. In the technology overview graphic, this functional group is subdivided into the two subgroups: “Collection/Storage” and “(Pre-)Treatment”. This allows a further classification for each of the listed technologies with regard to their function: collection and storage, (pre-) treatment only or both.Refers to the methods through which products are returned to the environment, either as useful resources or reduced-risk materials. Some products can also be cycled back into a system (e.g. by using treated greywater for flushing).A functional group is a grouping of technologies that have similar functions. The compendium proposes five different functional groups from which technologies can be chosen to build a sanitation system:
User interface (U), Collection and Storage/Treatment (S), Conveyance (C), (Semi-) Centralised Treatment (T), Use and/or Disposal (U).
A sanitation system is a multi-step process in which sanitation products such as human excreta and wastewater are managed from the point of generation to the point of use or ultimate disposal. It is a context-specific series of technologies and services for the management of these sanitation products, i.e. for their collection, containment, transport, treatment, transformation, use or disposal. A sanitation system comprises functional groups of technologies that can be selected according to context. By selecting technologies from each applicable functional group, considering the incoming and outgoing products, and the suitability of the technologies in a particular context, a logical, modular sanitation system can be designed. A sanitation system also includes the management and operation and maintenance (O & M) required to ensure that the system functions safely and sustainably. The utilisation of products derived from a sanitation system.
The liquid that has passed through a filter.
A sanitation system in which excreta and wastewater are collected and stored or treated on the plot where they are generated.
The means of safely collecting and hygienically disposing of excreta and liquid
wastes for the protection of public health and the preservation of the quality of public water bodies and, more generally, of the environment.

Waste matter that is transported through the sewer.
An open channel or closed pipe used to convey sewage. See C.3 and C.4
Used water from any combination of domestic, industrial, commercial or agricultural activities, surface runoff/stormwater, and any sewer inflow/infiltration.

As wastewater (greywater or blackwater after primary treatment) percolates through the soil from the soak pit, small particles are filtered out by the soil matrix and organics are digested by microorganisms. Thus, Soak Pits are best suited for soil with good absorptive properties; clay, hard packed or rocky soil is not appropriate.

Design Considerations

The Soak Pit should be between 1.5 and 4 m deep, and as a rule of thumb, never less than 2 m above the highest groundwater table. It should be located at a safe distance from a drinking water source (ideally more than 30 m). The Soak Pit should be kept away from high-traffic areas so that the soil above and around it is not compacted. It can be left empty and lined with a porous material to provide support and prevent collapse, or left unlined and filled with coarse rocks and gravel. The rocks and gravel will prevent the walls from collapsing, but will still provide adequate space for the wastewater. In both cases, a layer of sand and fine gravel should be spread across the bottom to help disperse the flow. To allow for future access, a removable (preferably concrete) lid should be used to seal the pit until it needs to be maintained. As the bottom may clog, the design should only consider the sidewall area. Preferably a percolation test is done to assess the leaching capacity of the soil.

Materials

Bricks and cement or wood are needed for lining and rocks and gravel for filling a soak pit. This filling can also replace the lining, by supporting the walls from inside.

Applicability

A Soak Pit exposed to raw wastewater will quickly clog. Soak Pits are designed to discharge pre-settled blackwater or greywater. The technology is appropriate for rural and peri-urban settlements. They depend on soil with a sufficient absorptive capacity (e.g. sandy soils) and are not appropriate for areas prone to flooding or with high groundwater tables. As Soak Pits are very low cost, cheap and easy to implement technologies for water based systems, they can be the first solution for wastewater discharge in an emergency. Once it is possible to provide better treatment to the wastewater, Soak Pits can potentially be upgraded or replaced.

Operation and Maintenance

A well-sized Soak Pit should last between 3 and 5 years without maintenance. To extend the life of a Soak Pit, the effluent must be clarified and/or filtered to prevent the excessive build-up of solids. Particles and biomass will eventually clog the pit so that it will need to be cleaned or moved. When the performance of the Soak Pit deteriorates, the material inside can be excavated and refilled.

Health and Safety

As long as the Soak Pit is not used for raw sewage, and as long as the previous collection and storage/treatment technology is functioning well, health concerns are minimal. The technology is located underground and, thus, humans and animals should have no contact with the effluent. Groundwater contamination can be an issue and the Soak Pit must be kept far away from any potential potable water source. Soil properties such as the permeability of the soil and groundwater level should be properly assessed X.3 to limit exposure of water sources to microbial contamination. The Sphere minimum standards on excreta management should be consulted for further guidance.

Costs

Soak pits are very low in cost for construction, operation and maintenance.

Social Considerations

A Soak Pit is a very low-cost and low-tech solution for discharging wastewater. Since the Soak Pit is odourless, installed underground and wastewater kept away from human contact, even the most sensitive communities may have little acceptance issues.